It's amazing. One little button. So much effect. dbx Type III Noise Reduction is an entirely new concept... virtually instantaneous encode/decode within the circuitry of the box. We started out to build the finest EQs possible, boxes with the heritage and performance to rival our famous 30 Series EQs. And to no one's surprise they came out awfully darn good. (Ask to see the Audio Precision plots compared to the competition.) But then, Roger (our chief engineer, a nice guy, as far as engineers go) got the crazy idea of putting this new noise reduction stuff in the box. We listened to it and were amazed. The EQs sounded great without it but with it the performance was nothing short of incredible. Check it out yourself and see. |
Connectors: | 1/4" TRS, female XLR (pin 2 hot), and barrier terminal strip |
Type: | Electronically balanced/unbalanced, RF filtered |
Impedance: | Balanced 40k, unbalanced 20k |
Max Input Level: | >+21dBu balanced or unbalanced |
CMRR: | >40dB, typically >55dB at 1kHz |
Connectors: | 1/4" TRS, male XLR (pin 2 hot), and barrier terminal strip |
Type: | Impedance-balanced/unbalanced, RF filtered |
Impedance: | Balanced 200, unbalanced 100 |
Max Output Level: | >+21dBu balanced/unbalanced into 2k or greater |
| >+18dBm balanced/unbalanced (into 600) |
Bandwidth: | 20Hz to 20kHz, +/-0.5dB |
Frequency Response: | <10Hz to >50kHz, +0.5/-3dB |
Noise Reduction In | (+/-6 and +/-15dB range): |
Signal-to-Noise: | >102dB, unweighted, ref: +4dBu, 22kHz measurement bandwidth |
Dynamic Range: | >120dB, unweighted |
Noise Reduction Out: | (+/-6dB range): |
Signal-to-Noise: | >94dB, unweighted, ref: +4dBu, 22kHz measurment bandwidth |
Dynamic Range: | >112dB, unweighted |
Noise Reduction Out: | (+/-15dB range): |
Signal-to-Noise: | >90dB, unweighted, ref: +4dBu, 22kHz measurement bandwidth |
Dynamic Range: | >108dB, unweighted |
THD+Noise: | <0.04%, 0.02% typical at +4dBu, 1kHz |
Noise Reduction: | Up to 20dB of dynamic broadband noise reduction |
Type III NR: | Activates dbx Type III Noise Reduction |
EQ Bypass: | Bypasses the graphic equalizer section in the signal path |
Low Cut (recessed): | Activates the 40Hz 18dB/octave Bessel high-pass filter |
Range (recessed): | Selects either +/- 6dB or +/- 15dB slider boost/cut range |
Output Level Meter: | 4-LED bar graph (Green, Green, Yellow, Red) at -10, 0, +10, and +18dBu |
Gain Reduction Meter: | 4-LED bar graph (all Red) at 0, 3, 6, and 10dB |
Type III NR Active: | Yellow LED |
EQ Bypass: | Red LED |
Clip: | Red LED |
Low Cut Active: | Red LED |
+/-6dB range: | Yellow LED |
+/-15dB range: | Red LED |
Operating Voltage: | 100VAC 50/60Hz, 120VAC 60Hz |
230VAC 50/60Hz | |
Power Consumption: | 12W |
Mains Connection: | IEC receptacle |
Dimensions: | 3.5" H X 19" W X 7.9" D (8.9cm x 48.3cm x 20.1cm) |
Weight: | 8.5 lbs. (3.9 kg) |
Shipping Weight: | 9.5 lbs. (4.3 kg) |
| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
상품이 장바구니에 담겼습니다.
바로 확인하시겠습니까?
상품이 찜 리스트에 담겼습니다.
바로 확인하시겠습니까?